Regular maintenance and cleaning will ensure a long life for the heating and cooling system as well as save you a few bucks. Keeping the air conditioner well maintained will ensure that you do not just save on cash on energy but ensure it remains in good condition for long, saving yours from early replacements. The heating and cooling professionals advise on regular attention to the AC systems to ensure they are in good working condition for high efficiency. The right time to make use of these tips is just before the cold season. Below are some steps to make sure HVAC in Long Beach CA is in good condition always.
The first thing you should do is to clean the fin of your system. Using a strong garden hose stream, spray via the fins of your unit from the inside. This will help flush out any debris or dust. You should never clean the fins using a pressure washer since the pressure can destroy the fins. In case the fins are dirty, use the fin cleaning sprays that are commercially available. Ensure you read the instructions of the manufacturer before using these products.
The next thing is to ensure you clean any area surrounding the unit. When you are done with it, remember to replace its fun cage. Using a rake, you should be able to remove any debris or leaves found outside its condenser. If there are some plants around the area, you should trim them to less than 2 feet. This is done to ensure the clean flow of air on the units. It is also good to cover the upper side of the condenser so as to prevent any debris from getting inside.
Ensure you level the system. As time passes, the pad where the condenser unit is placed might start to trip due to soil settling under it. If the condenser is not on the level, it may cause the compressor inside to fail early. Check if the condenser is on the level and brings it to level using shims that are resistant to rot.
Clean the evaporator coil. This one is found inside the unit. It is located on the inside furnace unit or blower. You will be required to take out some foil duct as well as a few bolts or screws. With the use of a soft brush, dust off the coil, and then with the use of commercially no-rinse coil cleaner, spray the coil. The spray will later form up and drop into the drain pan. Clean this drain pan with some bleach, hot water, and soap.
It is important to clean the evaporator drain. Humid and warm air inside the house is blown through this coil. It is also here that you will get the right temperature in the house. Inside, humidity is condensed to liquid water and then drip into the pan below.
Replace the blower filter. You should change the filter of your heating and cooling system at least two times every year. That is, before the onset of the heating seasons and then before the onset of the cooling season. You should, however, replace the blower filter often in case you live in a dusty area.
Before you start on any maintenance work, it is very essential that you know what you are doing. For the best results on the units, involve a qualified technician to handle the task. It will save you a lot of money since they will work efficiently to ensure the units are running smooth without the need of buying another one.
The first thing you should do is to clean the fin of your system. Using a strong garden hose stream, spray via the fins of your unit from the inside. This will help flush out any debris or dust. You should never clean the fins using a pressure washer since the pressure can destroy the fins. In case the fins are dirty, use the fin cleaning sprays that are commercially available. Ensure you read the instructions of the manufacturer before using these products.
The next thing is to ensure you clean any area surrounding the unit. When you are done with it, remember to replace its fun cage. Using a rake, you should be able to remove any debris or leaves found outside its condenser. If there are some plants around the area, you should trim them to less than 2 feet. This is done to ensure the clean flow of air on the units. It is also good to cover the upper side of the condenser so as to prevent any debris from getting inside.
Ensure you level the system. As time passes, the pad where the condenser unit is placed might start to trip due to soil settling under it. If the condenser is not on the level, it may cause the compressor inside to fail early. Check if the condenser is on the level and brings it to level using shims that are resistant to rot.
Clean the evaporator coil. This one is found inside the unit. It is located on the inside furnace unit or blower. You will be required to take out some foil duct as well as a few bolts or screws. With the use of a soft brush, dust off the coil, and then with the use of commercially no-rinse coil cleaner, spray the coil. The spray will later form up and drop into the drain pan. Clean this drain pan with some bleach, hot water, and soap.
It is important to clean the evaporator drain. Humid and warm air inside the house is blown through this coil. It is also here that you will get the right temperature in the house. Inside, humidity is condensed to liquid water and then drip into the pan below.
Replace the blower filter. You should change the filter of your heating and cooling system at least two times every year. That is, before the onset of the heating seasons and then before the onset of the cooling season. You should, however, replace the blower filter often in case you live in a dusty area.
Before you start on any maintenance work, it is very essential that you know what you are doing. For the best results on the units, involve a qualified technician to handle the task. It will save you a lot of money since they will work efficiently to ensure the units are running smooth without the need of buying another one.
About the Author:
If you are looking for info about Newport Beach air conditioner installation, come to our web pages online here today. Additional details are available at http://completecomfort-hvac.com now.
Aucun commentaire:
Enregistrer un commentaire